MEDIAD(1M) MEDIAD(1M)
mediad - removable media daemon
mediad
mediad [ -l level ] [ -f ] ] [ -n ] -a
mediad [ -d ] -f
mediad -k
mediad -l level
mediad [ -l level ] -e [ ctlr ] ID [ LUN ] | dir | device
mediad [ -l level ] -u
mediad is a daemon that monitors the removable media devices on a system.
When media is inserted, mediad scans the media for filesystems and mounts
them. When a user issues the eject command, eject sends mediad a
message, and mediad dismounts the filesystems and ejects the media.
N.B.: Because data corruption and loss will occur if media is forcibly
removed without unmounting any filesystems present on the media, always
eject disk media using either the eject command or the Eject selection in
the desktop pop-up menu for the device.
For all options other than -e, -u, and -m, mediad may only be invoked by
the superuser.
mediad reads configuration options from its configuration file,
/etc/config/mediad.config. mediad continually monitors its configuration
file. When that file changes, mediad immediately updates device status
to match the file. The configuration file is described below under
CONFIGURATION FILE SYNTAX.
mediad also provides information to the IRIX Interactive Desktop and
system administration tools which they use to draw the icons representing
removable media devices.
mediad monitors these device types:
CDROM CD-ROM
dat DAT tape
floppy Insite floptical disk, Teac SCSI floppy disk
jaz Iomega Jaz disk
LS-120 LS-120 I-O Data 120MB floppy-compatible disk
optical Sony SMO-521 and Pinnacle Sierra magneto-optical disks
syquest SyQuest EZ135, 88, 105, 200, and 270 Mb disks
Page 1
MEDIAD(1M) MEDIAD(1M)
tape QIC 24, 150, 1000, and 1350 tapes, IBM 3480 tape, Exabyte 8 mm
tape, and DLT tape
zip Iomega Zip disk
Note that CDROM, dat, floppy, LS-120 and tape are sold and supported by
SGI. The rest (jaz, optical, syquest, zip) are not sold or supported by
SGI.
mediad recognizes these filesystem types on devices that support them.
See filesystems(4).
cdda Compact Disk Digital Audio
dos IBM PC DOS
efs Silicon Graphics Extent File System
iso9660 ISO 9660 filesystem for CD-ROM, also the High Sierra, Rock
Ridge and PhotoCD extensions.
hfs Apple Macintosh Hierarchical File System
xfs Silicon Graphics XFS File System
If a disk has several nonoverlapping partitions, mediad mounts them all
by default. If it has overlapping partitions, mediad mounts the
filesystem type that appears first in the list above. You can override
the default behavior using the configuration file.
mediad uses the following rules to choose the directory where it mounts a
filesystem.
1. If the configuration file contains an applicable mount command, and
the mount command specifies a directory, that directory is used.
2. Otherwise, if mediad is only mounting one partition from the device,
then the device name is used. If there is more than one device of a
given type, a number is appended to every device except the first.
(For example, filesystems from two Zip drives are mounted at /zip
and /zip2.)
3. Otherwise, the directory name is made by concatenating the device
name, the filesystem type, and the partition number. (For example,
three DOS partitions on a Jaz drive are mounted at
/jaz/dos.partition1, /jaz/dos.partition2 and /jaz/dos.partition3.)
mediad uses the dynamic shared objects (DSOs) in /usr/devicelib. There
is one DSO for each device type mediad understands and one DSO for each
filesystem type.
Page 2
MEDIAD(1M) MEDIAD(1M)
-a Start mediad in the background. (This is the default when no
arguments are specified)
-d Turn on the dsdebug variable of dslib(3X) which enables voluminous
SCSI command tracing. The -d option must be used with the -f
option.
-e device
Eject the given device. The device must be specified as described
under CONFIGURATION FILE SYNTAX, below.
-e directory
Eject the device containing the filesystem mounted at the given
directory.
-f Start mediad in the foreground. When running in the foreground,
mediad does not fork at startup. The -f option also sets the
default log level to LOG_DEBUG, and log messages are directed to
mediad's standard error instead of to syslogd(1M).
-k Send a message to mediad telling it to exit. When mediad exits, it
dismounts all the filesystems it has mounted.
-l level
When used alone, sends a message to the currently running mediad to
log all messages of priority level and higher. When used with -a,
-f, -e or -u option, the -l option affects the current mediad
process instead of sending a message.
-n Mount all filesystems with the nosuid mount option. When -n is
specified, nosuid is specified in the options argument of all
mount(1M) commands that mediad runs.
-u Eject the default device. On systems with more than one removable
media device, this command should not be used, because the default
device is not predictable.
EXAMPLE COMMANDS
mediad -l 7 -a
Start mediad in the background with full debugging output.
mediad -f
Start mediad in the foreground with full debugging output.
mediad -e 0 4 0
mediad -e 0 4
mediad -e 4
mediad -e /dev/scsi/sc0d4l0
mediad -e /dev/rdsk/dks0d4s7
mediad -e /dev/rmt/tps0d4
mediad -e /dev/rdsk/fds0d4.3.5hi
Page 3
MEDIAD(1M) MEDIAD(1M)
Each of these commands ejects the device at SCSI controller 0, ID 4,
LUN 0.
mediad -e /floppy
Eject the device with a filesystem mounted at the directory /floppy.
CONFIGURATION FILE SYNTAX [Toc] [Back] mediad's configuration file, /etc/config/mediad.config, is optional, and
is not present in the system as shipped. It may be created at any time
as needed. The file consists of one or more configuration commands, with
one command per line. Comments begin with a # character and continue to
the end of the line.
A device specification specifies a device. It consists of the keyword
device followed by the name of a device special file. The special file
is only used to determine the device's address - the type of device is
unimportant. Mediad recognizes these device types.
scsi generic SCSI device
dksc SCSI disk device
tpsc SCSI tape device
smfd SCSI floppy/floptical device
A filesystem specification specifies a pattern to match filesystems. A
filesystem specification consists of the keyword filesystem, the name of
a device special file, a filesystem type, and, optionally, the keyword
partition followed by a partition number. If the partition number is
omitted, the filesystem specification matches a filesystem covering the
whole disk. In general, within a filesystem specification the device
should be named using the device special file name that mediad uses by
default. An exception occurs when using ISO 9660 CD-ROMs. For ISO 9660
filesystems the CD-ROM device must be specified by its entry in the
directory /dev/scsi.
These are the configuration file's commands.
ignore device specification
Tells mediad not to monitor this device. The device will have a
generic device icon on the desktop, and mediad will not access the
device.
ignore filesystem specification
Tells mediad not to mount filesystems matching this specification.
monitor device specification
Tells mediad to monitor this device. This is the default.
Page 4
MEDIAD(1M) MEDIAD(1M)
The monitor command has these optional parameters.
inschk number
Tells mediad to check for media insertion every number seconds.
The default is 3.
rmvchk number
Tells mediad to check for media removal every number seconds.
The default is 45.
mount filesystem specification
Tells mediad to mount filesystems matching this specification.
Filesystems that match a mount command will be preferentially
mounted over filesystems that do not, so you can use the mount
command to override mediad's filesystem precedence order.
The mount command has these optional parameters.
directory path
Tells mediad to mount the filesystem at this directory.
options list
Tells mediad to pass these mount options to the mount command
when mounting the filesystem. See fstab(4) for a list of valid
options.
shared
Tells mediad to export the filesystem for remote NFS access
after mounting it. If the filesystem's mount directory is
listed in /etc/exports (see exports(4)), the export options
listed there are used. Otherwise, the filesystem is exported
read-only to all hosts. See the description of the share
command below.
unshared
Tells mediad not to export the filesystem.
share device specification
Tells mediad to share the specified device. A shared device can be
accessed from other machines through the IRIX Interactive Desktop.
A shared device's filesystems are also exported by default, although
you can override that behavior via the mount command, described
above.
SAMPLE CONFIGURATION FILE [Toc] [Back] # ignore a tape device completely.
ignore device /dev/rmt/tps0d6
# do not mount audio CDs on this CD-ROM drive.
ignore filesystem /dev/scsi/sc0d4l0 cdda
# check a floppy device for insertion and removal
Page 5
MEDIAD(1M) MEDIAD(1M)
# every 60 seconds
monitor device /dev/scsi/sc0d2l0 inschk 60 rmvchk 60
# mount HFS (Macintosh) filesystems on a CD-ROM
# preferentially over other filesystem types
mount filesystem /dev/scsi/sc0d4l0 hfs
# mount EFS filesystems on the given CD-ROM at
# the directory "/data", disallowing set-UID programs.
mount filesystem /dev/dsk/dks0d4s7 efs directory /data options nosuid
# share a Zip drive
share device /dev/scsi/sc0d6l0
/etc/config/mediad.config configuration file
/etc/init.d/mediad mediad startup and shutdown script
/etc/config/mediad.options command line arguments mediad is started
with during system initialization
/usr/lib/devicelib/dev_*.so device DSOs
/usr/lib/devicelib/fmt_*.so filesystem format DSOs
eject(1), mount(1M), exports(4), filesystems(4), fstab(4), scsi(7),
dksc(7), tpsc(7), smfd(7).
For a complete list of devices supported on SGI platforms, please contact
your support provider.
PPPPaaaaggggeeee 6666 [ Back ]
|
