isdndecode -- isdn4bsd ISDN protocol decode utility
isdndecode [-a] [-b] [-d] [-f filename] [-h] [-i] [-l] [-o] [-p filename]
[-u number] [-x] [-B] [-P] [-R unit] [-T unit]
The isdndecode utility is part of the isdn4bsd package and is used to
provide the user with a detailed mnemonic display of the layers 1, 2 and
3 protocol activities on the D channel and hex dump of the B channel(s)
activities.
Together with two passive supported cards and an easy to build cable it
can also be used to monitor the complete traffic on a S0 bus providing S0
bus analyzer features.
The isdndecode utility is only available for passive supported cards.
The following options can be used:
-a Run isdndecode in analyzer mode by using two passive cards and a
custom cable which can be build as described in the file
cable.txt in the isdn4bsd source distribution. One card acts as a
receiver for the transmitting direction on the S0 bus while the
other card acts as a receiver for the receiving direction on the
S0 bus. Complete traffic monitoring is possible using this setup.
-b switch B channel tracing on (default off).
-d switch D channel tracing off (default on).
-f Use filename as the name of a file into which to write tracing
output (default filename is isdndecode<n> where n is the number
of the unit to decode).
-h switch display of header off (default on).
-i print layer 1 (I.430) INFO signals to monitor layer 1 activity
(default off).
-l switch displaying of Layer 2 (Q.921) frames off (default on).
-o switch off writing decode output to a file (default on).
-p Use filename as the name of a file used for the -B and -P options
(default filename is isdntracebin<n> where n is the number of the
unit to decode).
-u Use number as the unit number of the controller card to decode
(default 0).
-x Decode Layer 3 packets with an unknown protocol discriminator.
-B Write undecoded binary decode data to a file for later or remote
analyzing (default off).
-P Read undecoded binary decode data from file instead from device
(default off).
-R Use unit as the receiving interface unit number in analyze mode.
-T Use unit as the transmitting interface unit number in analyze
mode.
When the USR1 signal is sent to a isdndecode process, the currently used
logfiles are reopened, so that logfile rotation becomes possible.
The decode output should be obvious. It is very handy to have the following
standard texts available when tracing ISDN protocols:
I.430 ISDN BRI layer 1 protocol description.
Q.921 ISDN D-channel layer 2 protocol description.
Q.931 ISDN D-channel layer 3 protocol description.
/dev/i4btrc<n>
The devicefile(s) used to get the decode messages for ISDN card
unit <n> out of the kernel.
The command:
isdndecode -f /var/tmp/isdn.decode
will start D channel tracing on passive controller 0 with all except B
channel tracing enabled and logs everything into the output file
/var/tmp/isdn.decode.
isdnd(8)
Still one left.
ITU Recommendations I.430, Q.920, Q.921, Q.930, Q.931
ITU Recommendation Q.932 (03/93), Q.950 (03/93)
ETSI Recommendation ETS 300 179 (10/92), ETS 300 180 (10/92)
ETSI Recommendation ETS 300 181 (04/93), ETS 300 182 (04/93)
ITU Recommendation X.208, X.209
The isdndecode utility and this manual page were written by Hellmuth
Michaelis <[email protected]>.
FreeBSD 5.2.1 February 21, 2000 FreeBSD 5.2.1 [ Back ] | 