diagnostics, splain - produce verbose warning diagnostics
Using the "diagnostics" pragma:
use diagnostics;
use diagnostics -verbose;
enable diagnostics;
disable diagnostics;
Using the "splain" standalone filter program:
perl program 2>diag.out
splain [-v] [-p] diag.out
The "diagnostics" Pragma
This module extends the terse diagnostics normally emitted
by both the perl compiler and the perl interpreter, augmenting
them with the more explicative and endearing
descriptions found in perldiag. Like the other pragmata,
it affects the compilation phase of your program rather
than merely the execution phase.
To use in your program as a pragma, merely invoke
use diagnostics;
at the start (or near the start) of your program. (Note
that this does enable perl's -w flag.) Your whole compilation
will then be subject(ed :-) to the enhanced diagnostics.
These still go out STDERR.
Due to the interaction between runtime and compiletime
issues, and because it's probably not a very good idea
anyway, you may not use "no diagnostics" to turn them off
at compiletime. However, you may control their behaviour
at runtime using the disable() and enable() methods to
turn them off and on respectively.
The -verbose flag first prints out the perldiag introduction
before any other diagnostics. The $diagnostics::PRETTY
variable can generate nicer escape sequences
for pagers.
Warnings dispatched from perl itself (or more accurately,
those that match descriptions found in perldiag) are only
displayed once (no duplicate descriptions). User code
generated warnings a la warn() are unaffected, allowing
duplicate user messages to be displayed.
The splain Program
While apparently a whole nuther program, splain is actually
nothing more than a link to the (executable) diagnos-
tics.pm module, as well as a link to the diagnostics.pod
documentation. The -v flag is like the "use diagnostics
-verbose" directive. The -p flag is like the $diagnostics::PRETTY
variable. Since you're post-processing with
splain, there's no sense in being able to enable() or dis-
able() processing.
Output from splain is directed to STDOUT, unlike the
pragma.
The following file is certain to trigger a few errors at
both runtime and compiletime:
use diagnostics;
print NOWHERE "nothing0;
print STDERR "This message should be unadorned.0;
warn "This is a user warning";
print "0IAGNOSTIC TESTER: Please enter a <CR> here: ";
my $a, $b = scalar <STDIN>;
print "0;
print $x/$y;
If you prefer to run your program first and look at its
problem afterwards, do this:
perl -w test.pl 2>test.out
./splain < test.out
Note that this is not in general possible in shells of
more dubious heritage, as the theoretical
(perl -w test.pl >/dev/tty) >& test.out
./splain < test.out
Because you just moved the existing stdout to somewhere
else.
If you don't want to modify your source code, but still
have on-the-fly warnings, do this:
exec 3>&1; perl -w test.pl 2>&1 1>&3 3>&- | splain
1>&2 3>&-
Nifty, eh?
If you want to control warnings on the fly, do something
like this. Make sure you do the "use" first, or you won't
be able to get at the enable() or disable() methods.
use diagnostics; # checks entire compilation phase
print "0ime for 1st bogus diags: SQUAWKINGS0;
print BOGUS1 'nada';
print "done with 1st bogus0;
disable diagnostics; # only turns off runtime warnings
print "0ime for 2nd bogus: (squelched)0;
print BOGUS2 'nada';
print "done with 2nd bogus0;
enable diagnostics; # turns back on runtime warnings
print "0ime for 3rd bogus: SQUAWKINGS0;
print BOGUS3 'nada';
print "done with 3rd bogus0;
disable diagnostics;
print "0ime for 4th bogus: (squelched)0;
print BOGUS4 'nada';
print "done with 4th bogus0;
Diagnostic messages derive from the perldiag.pod file when
available at runtime. Otherwise, they may be embedded in
the file itself when the splain package is built. See
the Makefile for details.
If an extant $SIG{__WARN__} handler is discovered, it will
continue to be honored, but only after the diagnos-
tics::splainthis() function (the module's $SIG{__WARN__}
interceptor) has had its way with your warnings.
There is a $diagnostics::DEBUG variable you may set if
you're desperately curious what sorts of things are being
intercepted.
BEGIN { $diagnostics::DEBUG = 1 }
Not being able to say "no diagnostics" is annoying, but
may not be insurmountable.
The "-pretty" directive is called too late to affect matters.
You have to do this instead, and before you load
the module.
BEGIN { $diagnostics::PRETTY = 1 }
I could start up faster by delaying compilation until it
should be needed, but this gets a "panic: top_level" when
using the pragma form in Perl 5.001e.
While it's true that this documentation is somewhat subserious,
if you use a program named splain, you should
expect a bit of whimsy. Tom Christiansen <[email protected]>, 25 June 1995.
perl v5.8.5 2002-11-06 4 [ Back ] |
