ntpdate - set the date and time via NTP
ntpdate [-bBdoqsuv] [-a key] [-e authdelay] [-k keyfile] [-o version]
[-p samples] [-t timeout] server [...]
ntpdate sets the local date and time by polling the Network Time Protocol
(NTP) server(s) given as the server arguments to determine the correct
time. It must be run as root on the local host. A number of samples
are obtained from each of the servers specified and a subset of
the NTP clock filter and selection algorithms are applied to select the
best of these. Note that the accuracy and reliability of ntpdate
depends on the number of servers, the number of polls each time it is
run and the interval between runs.
ntpdate can be run manually as necessary to set the host clock, or it
can be run from the host startup script to set the clock at boot time.
This is useful in some cases to set the clock initially before starting
the NTP daemon ntpd. It is also possible to run ntpdate from a cron
script. However, it is important to note that ntpdate with contrived
cron scripts is no substitute for the NTP daemon, which uses sophisticated
algorithms to maximize accuracy and reliability while minimizing
resource use. Finally, since ntpdate does not discipline the host clock
frequency as does ntpd, the accuracy using ntpdate is limited.
Time adjustments are made by ntpdate in one of two ways. If ntpdate
determines the clock is in error more than 0.5 second it will simply
step the time by calling the system settimeofday() routine. If the
error is less than 0.5 seconds, it will slew the time by calling the
system adjtime() routine. The latter technique is less disruptive and
more accurate when the error is small, and works quite well when ntpdate
is run by cron every hour or two.
ntpdate will decline to set the date if an NTP server daemon (e.g.,
ntpd) is running on the same host. When running ntpdate on a regular
basis from cron as an alternative to running a daemon, doing so once
every hour or two will result in precise enough timekeeping to avoid
stepping the clock.
-a key Enable the authentication function and specify the key identifier
to be used for authentication as the argument keyntpdate.
The keys and key identifiers must match in both the client and
server key files. The default is to disable the authentication
function.
-B Force the time to always be slewed using the adjtime() system
call, even if the measured offset is greater than +-128 ms. The
default is to step the time using settimeofday() if the offset
is greater than +-128 ms. Note that, if the offset is much
greater than +-128 ms in this case, that it can take a long time
(hours) to slew the clock to the correct value. During this
time. the host should not be used to synchronize clients.
-b Force the time to be stepped using the settimeofday() system
call, rather than slewed (default) using the adjtime() system
call. This option should be used when called from a startup file
at boot time.
-d Enable the debugging mode, in which ntpdate will go through all
the steps, but not adjust the local clock. Information useful
for general debugging will also be printed.
-e authdelay
Specify the processing delay to perform an authentication function
as the value authdelay, in seconds and fraction (see ntpd
for details). This number is usually small enough to be negligible
for most purposes, though specifying a value may improve
timekeeping on very slow CPU's.
-k keyfile
Specify the path for the authentication key file as the string
keyfile. The default is /etc/ntp.keys. This file should be in
the format described in ntpd.
-o version
Specify the NTP version for outgoint packets as the integer version,
which can be 1 or 2. The default is 3. This allows ntpdate
to be used with older NTP versions.
-p samples
Specify the number of samples to be acquired from each server as
the integer samples, with values from 1 to 8 inclusive. The
default is 4.
-q Query only - don't set the clock.
-s Divert logging output from the standard output (default) to the
system syslog facility. This is designed primarily for convenience
of cron scripts.
-t timeout
Specify the maximum time waiting for a server response as the
value timeout, in seconds and fraction. The value is is rounded
to a multiple of 0.2 seconds. The default is 1 second, a value
suitable for polling across a LAN.
-u Direct ntpdate to use an unprivileged port or outgoing packets.
This is most useful when behind a firewall that blocks incoming
traffic to privileged ports, and you want to synchronise with
hosts beyond the firewall. Note that the -d option always uses
unprivileged ports.
-v Be verbose. This option will cause ntpdate's version identification
string to be logged.
/etc/ntp.keys
- encryption keys used by ntpdate.
The slew adjustment is actually 50% larger than the measured offset,
since this (it is argued) will tend to keep a badly drifting clock more
accurate. This is probably not a good idea and may cause a troubling
hunt for some values of the kernel variables tick and tickadj.
David L. Mills ([email protected])
This manpage converted from html to roff by Fabrizio Polacco <fpo[email protected]>
ntpdate(1)
[ Back ] |
