ifconfig - configure a network interface
ifconfig [interface]
ifconfig interface [aftype] options | address ...
Ifconfig is used to configure the kernel-resident network interfaces.
It is used at boot time to set up interfaces as necessary. After that,
it is usually only needed when debugging or when system tuning is
needed.
If no arguments are given, ifconfig displays the status of the currently
active interfaces. If a single interface argument is given, it
displays the status of the given interface only; if a single -a argument
is given, it displays the status of all interfaces, even those
that are down. Otherwise, it configures an interface.
If the first argument after the interface name is recognized as the
name of a supported address family, that address family is used for
decoding and displaying all protocol addresses. Currently supported
address families include inet (TCP/IP, default), inet6 (IPv6), ax25
(AMPR Packet Radio), ddp (Appletalk Phase 2), ipx (Novell IPX) and
netrom (AMPR Packet radio).
interface
The name of the interface. This is usually a driver name followed
by a unit number, for example eth0 for the first Ethernet
interface.
up This flag causes the interface to be activated. It is implicitly
specified if an address is assigned to the interface.
down This flag causes the driver for this interface to be shut down.
[-]arp Enable or disable the use of the ARP protocol on this interface.
[-]promisc
Enable or disable the promiscuous mode of the interface. If
selected, all packets on the network will be received by the
interface.
[-]allmulti
Enable or disable all-multicast mode. If selected, all multicast
packets on the network will be received by the interface.
metric N
This parameter sets the interface metric.
mtu N This parameter sets the Maximum Transfer Unit (MTU) of an interface.
dstaddr addr
Set the remote IP address for a point-to-point link (such as
PPP). This keyword is now obsolete; use the pointopoint keyword
instead.
netmask addr
Set the IP network mask for this interface. This value defaults
to the usual class A, B or C network mask (as derived from the
interface IP address), but it can be set to any value.
add addr/prefixlen
Add an IPv6 address to an interface.
del addr/prefixlen
Remove an IPv6 address from an interface.
tunnel aa.bb.cc.dd
Create a new SIT (IPv6-in-IPv4) device, tunnelling to the given
destination.
irq addr
Set the interrupt line used by this device. Not all devices can
dynamically change their IRQ setting.
io_addr addr
Set the start address in I/O space for this device.
mem_start addr
Set the start address for shared memory used by this device.
Only a few devices need this.
media type
Set the physical port or medium type to be used by the device.
Not all devices can change this setting, and those that can vary
in what values they support. Typical values for type are
10base2 (thin Ethernet), 10baseT (twisted-pair 10Mbps Ethernet),
AUI (external transceiver) and so on. The special medium type
of auto can be used to tell the driver to auto-sense the media.
Again, not all drivers can do this.
[-]broadcast [addr]
If the address argument is given, set the protocol broadcast
address for this interface. Otherwise, set (or clear) the
IFF_BROADCAST flag for the interface.
[-]pointopoint [addr]
This keyword enables the point-to-point mode of an interface,
meaning that it is a direct link between two machines with
nobody else listening on it.
If the address argument is also given, set the protocol address
of the other side of the link, just like the obsolete dstaddr
keyword does. Otherwise, set or clear the IFF_POINTOPOINT flag
for the interface.
hw class address
Set the hardware address of this interface, if the device driver
supports this operation. The keyword must be followed by the
name of the hardware class and the printable ASCII equivalent of
the hardware address. Hardware classes currently supported
include ether (Ethernet), ax25 (AMPR AX.25), ARCnet and netrom
(AMPR NET/ROM).
multicast
Set the multicast flag on the interface. This should not normally
be needed as the drivers set the flag correctly themselves.
address
The IP address to be assigned to this interface.
txqueuelen length
Set the length of the transmit queue of the device. It is useful
to set this to small values for slower devices with a high
latency (modem links, ISDN) to prevent fast bulk transfers from
disturbing interactive traffic like telnet too much.
Since kernel release 2.2 there are no explicit interface statistics for
alias interfaces anymore. The statistics printed for the original
address are shared with all alias addresses on the same device. If you
want per-address statistics you should add explicit accounting rules
for the address using the ipchains(8) command.
Since net-tools 1.60-4 ifconfig is printing byte counters with SI
units. So 1 KiB are 2^10 byte. Note, the numbers are truncated to one
decimal (which can by quite a large error if you consider 0.1 PiB is
112.589.990.684.262 bytes :)
Interrupt problems with Ethernet device drivers fail with EAGAIN (SIOC-
SIIFLAGS: Resource temporarily unavailable) it is most likely a interrupt
conflict. See http://www.scyld.com/expert/irq-conflict.html for
more information.
/proc/net/socket
/proc/net/dev
/proc/net/if_inet6
While appletalk DDP and IPX addresses will be displayed they cannot be
altered by this command.
route(8), netstat(8), arp(8), rarp(8), ipchains(8)
http://physics.nist.gov/cuu/Units/binary.html - Prefixes for binary
multiples
Fred N. van Kempen, <[email protected]>
Alan Cox, <[email protected]>
Phil Blundell, <[email protected]>
Andi Kleen;
Bernd Eckenfels, <[email protected]>
net-tools 11 Nov 2001 IFCONFIG(8)
[ Back ] |
